Encapsulation HDLC, loopback not set, keepalive set (10 sec)
While there's only one D-channel in BRI, PRI (US) and PRI (EU), the bandwidth of that D-channel does vary from BRI to PRI. It's 16 kbps in BRI and 64 kbps in both PRI versions.
The global command isdn switch-type must be configured before you can even begin to have ISDN work. show isdn status will tell you whether or not you've done this correctly.
R2#show isdn status
**** No Global ISDN Switchtype currently defined ****
ISDN BRI0 interface
dsl 0, interface ISDN Switchtype = none
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
PAP allows passwords to be different; CHAP requires that they be the same.
PAP requires the ?ppp pap sent-username? interface-level command. CHAP has no equivalent command.
Define interesting traffic with dialer-list and link that list to the interface with dialer-group.
R2#conf t
R2(config)#dialer-list 1 proto ip permit
R2(config)#int bri0
R2(config-if)#dialer-group 1
The dialer idle-timeout value is expressed in seconds, not minutes. (Even IOS Help isn't totally clear on this.)
R2(config)#int bri0
R2(config-if)#dialer-group 1
R2(config-if)#dialer idle-timeout ?
<1-2147483> Idle timeout before disconnecting a call
R2(config-if)#dialer idle-timeout 120
Dialer map maps a remote IP address to a remote phone number. You never dial the local router's phone number.
dialer load-threshold requires the ppp multilink command to be configured, and the value of dialer load-threshold is expressed as a ratio of 255, NOT 100. For example, if you want the second b-channel to come up when the first reaches 50% of capacity, the value to express with dialer load-threshold would be 50% of 255 ? which equals 127.
R2(config)#int bri0
R2(config-if)#encap ppp
R2(config-if)#ppp multilink
R2(config-if)#dialer load-threshold ?
<1-255> Load threshold to place another call
Success on the CCNA exam depends on knowing the details. Keep studying, keep practicing on real Cisco routers and switches, keep a positive attitude, and you're on your way to CCNA exam success!
Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client.
Even if you weren't going to get fired for not showing up, it's certainly unfair to the client. You've got a professional obligation, and you should be there on time.
Now, what's this got to do with you becoming a CCNA or CCNP? Plenty. Because when it comes to your study time, you're the client. You owe it to yourself to show up. You would never blow off an appointment to meet a client to get some important work done.
First, though, you have to make that appointment with yourself! Schedule your CCNA / CCNP study time, and keep that appointment as you would with a client. Turn off the TV, your cell, your iPod, and everything else electronic that you carry around. Believe it or not, the world can survive with being in contact with you for an hour or so! You might even like it!
Getting certified isn't about how many hours, days, or weeks you spend studying. It's about how much quality time you put in. Be honest with yourself and realize that you're better off with 45 minutes of uninterrupted study as you would be with three hours of constantly interrupted study.
Don't blow off an appointment to yourself, either. Schedule the time, be there on time, get your study done, and you're one step closer to your CCNA and CCNP!
Chris Bryant has sinced written about articles on various topics from CISCO CCNA, Personal Desktop and Cisco CCNP. Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free and CCNP tutorials! Pass the. Chris Bryant's top article generates over 27100 views. to your Favourites.