Print Article for : Medical Assistant Certification Exam

Your Online Guide » Science & Technology » CCNA Exam Guide

[M353]Medical Assistant Certification Exam

by Chris Bryant, Chr

The Cisco-proprietary version of HDLC is the default encapsulation type for serial and ISDN interfaces.

R2#show interface serial0

Serial0 is up, line protocol is up

Hardware is HD64570

MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, rely 255/255, load 1/255

Encapsulation HDLC, loopback not set, keepalive set (10 sec)

While there's only one D-channel in BRI, PRI (US) and PRI (EU), the bandwidth of that D-channel does vary from BRI to PRI. It's 16 kbps in BRI and 64 kbps in both PRI versions.

The global command isdn switch-type must be configured before you can even begin to have ISDN work. show isdn status will tell you whether or not you've done this correctly.

R2#show isdn status

**** No Global ISDN Switchtype currently defined ****

ISDN BRI0 interface

dsl 0, interface ISDN Switchtype = none

Layer 1 Status:

DEACTIVATED

Layer 2 Status:

Layer 2 NOT Activated

Layer 3 Status:

0 Active Layer 3 Call(s)

PAP allows passwords to be different; CHAP requires that they be the same.

PAP requires the “ppp pap sent-username” interface-level command. CHAP has no equivalent command.

Define interesting traffic with dialer-list and link that list to the interface with dialer-group.

R2#conf t

R2(config)#dialer-list 1 proto ip permit

R2(config)#int bri0

R2(config-if)#dialer-group 1

The dialer idle-timeout value is expressed in seconds, not minutes. (Even IOS Help isn't totally clear on this.)

R2(config)#int bri0

R2(config-if)#dialer-group 1

R2(config-if)#dialer idle-timeout ?

Idle timeout before disconnecting a call

R2(config-if)#dialer idle-timeout 120

Dialer map maps a remote IP address to a remote phone number. You never dial the local router's phone number.

dialer load-threshold requires the ppp multilink command to be configured, and the value of dialer load-threshold is expressed as a ratio of 255, NOT 100. For example, if you want the second b-channel to come up when the first reaches 50% of capacity, the value to express with dialer load-threshold would be 50% of 255 – which equals 127.

R2(config)#int bri0

R2(config-if)#encap ppp

R2(config-if)#ppp multilink

R2(config-if)#dialer load-threshold ?

Load threshold to place another call

Success on the CCNA exam depends on knowing the details. Keep studying, keep practicing on real Cisco routers and switches, keep a positive attitude, and you're on your way to CCNA exam success!

Inverse ARP starts working as soon as you open the serial interface. This protocol performs dynamic Frame Relay mapping, but you don't have to enable it - it's already enabled as soon as you enter the command "encapsulation frame-relay".

When you're configuring Frame Relay map statements manually, remember that you're mapping the local DLCI to the remote IP address.

When you run "show frame map", the word "dynamic" indicates mappings created by Inverse ARP, and "static" indicates it was manually created.

To spot possible LMI type mismatches, run "show frame lmi". A large number of Status Timeouts indicates that there may be an LMI problem between your router and the frame relay switch.

This last one is for the many of you building CCNA home labs. A frame relay switch is a great addition to your lab! While you're busy putting the configuration together, don't forget the global command "frame-relay switching" - it's this command that allows a Cisco router to act as a frame relay switch!

Article Source : CCNA Exam Guide

Chris Bryant has sinced written about articles on various topics from CISCO CCNA, Personal Desktop and Cisco CCNP. . Chris Bryant's top article generates over 27100 views. to your Favourites.