Print Article for : Ccnp Bcmsn Exam Certification

Your Online Guide » Science & Technology » CCNA Study Guide

[C314]Ccnp Bcmsn Exam Certification

by Chris Bryant, Chr

BCMSN exam success and earning your CCNP certification requires you to add to your knowledge of VLAN configuration. When you studied for your CCNA exam, you learned how to place ports into a VLAN and what the purpose of VLANs was, but you may not be aware that there are two types of VLAN membership. To pass the BCMSN exam, you must know the details of both types.

In this tutorial, we'll take a look at the VLAN type you are most familiar with, the "static VLAN". As you know, VLANs are a great way to create smaller broadcast domains in your network. Host devices connected to a port belonging to one VLAN will receive broadcasts and multicasts only if they were originated by another host in that same VLAN. The drawback is that without the help of a Layer 3 switch or a router, inter-VLAN communication cannot occur.

The actual configuration of a static VLAN is simple enough. In this example, by placing switch ports 0/1 and 0/2 into VLAN 12, the only broadcasts and multicasts hosts connected to those ports will receive are the ones transmitted by ports in VLAN 12.

SW1(config)#int fast 0/1

SW1(config-if)#switchport mode access

SW1(config-if)#switchport access vlan 12

% Access VLAN does not exist. Creating vlan 12

SW1(config-if)#int fast 0/2

SW1(config-if)#switchport mode access

SW1(config-if)#switchport access vlan 12

One of the many things I love about Cisco switches and routers is that if you have forgotten to do something, the Cisco device is generally going to remind you or in this case actually do it for you. I placed port 0/1 into a VLAN that did not yet exist, so the switch created it for me!

There are two commands needed to place a port into a VLAN. By default, these ports are running in dynamic desirable trunking mode, meaning that the port is actively attempting to form a trunk with a remote switch in order to send traffic between the two switches. The problem is that a trunk port belongs to all VLANs by default, and we want to put this port into a single VLAN only. To do so, we run the switchport mode access command to make the port an access port, and access ports belong to one and only one VLAN. After doing that, we placed the port into VLAN 12 with the switchport access vlan 12 command. Running the switchport mode access command effectively turns trunking off on that port.

The hosts are unaware of VLANs; they simply assume the VLAN membership of the port they're connected to. But that's not quite the case with dynamic VLANs, which we'll examine in the next part of this BCMSN tutorial.

Multicasting is a vital topic on your BCMSN, CCNP, and CCIE exams, and it can also be very confusing when you first start studying it. Multicasting uses concepts that are unlike anything you've run into in your routing protocol studies, and that can throw you at first. I speak from experience that multicasting is like any other Cisco technology - learn the basics, master the fundamentals, and then build your skills on that foundation.

One such fundamental is the RPF Check, or Reverse Path Forwarding Check.

A fundamental difference between unicasting and multicasting is that a unicast is routed by sending it toward the destination, while a multicast is routed by sending it away from its source.

"toward the destination" and "away from its source" sound like the same thing, but they're not. A unicast is going to follow a single path from source to destination. The only factor the routers care about is the destination IP address - the source IP address isn't a factor.

With multicast routing, the destination is a multicast IP group address. It's the multicast router's job to decide which paths will lead back to the source (upstream) and which paths are downstream from the source. Reverse Path Forwarding refers to the router's behavior of sending multicast packets away from the source rather than toward a specific destination.

The RPF Check is run against any incoming multicast packet. The multicast router examines the interface that the packet arrived on. If the packet comes in on an upstream interface - that is, an interface found on the reverse path that leads back to the source - the packet passes the check and will be forwarded. If the packet comes in on any other interface, the packet is dropped.

The RPF Check serves to verify the integrity of your multicasting network, and also serves as a reminder that the basic operation of multicasting is a lot different than unicasting!

Article Source : CCNA Study Guide

Chris Bryant has sinced written about articles on various topics from CISCO CCNA, Personal Desktop and Cisco CCNP. Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free and. Chris Bryant's top article generates over 27100 views. to your Favourites.