Print Article for : Ccna 3 Exam Answers

Your Online Guide » Science & Technology » CCNA Exam Guide

[C313]Ccna 3 Exam Answers

by Chris Bryant, Chr

A Cisco router is a DTE by default, but directly connecting two DTEs with a DCE/DTE cable is not enough. In the following example, R1 and R3 are directly connected at their Serial1 interfaces. The line goes up briefly after being opened, but the line protocol goes down after about 30 seconds.

R3(config-if)#int s1

R3(config-if)#ip address 172.12.13.3 255.255.255.0

R3(config-if)#no shutdown

2d18h: %LINK-3-UPDOWN: Interface Serial1, changed state to up

2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up

R3(config-if)#

2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down

The problem is that one of the routers needs to act as the DCE in order for the line protocol to come up and stay up. If this were your CCNA / CCNP home lab, you could just go over and look at the DTE/DCE cable to see which router had the DCE end of the cable attached. In this example, though, we don't have physical access to the routers. How can we tell which router has the DCE end of the cable attached?

R3#show controller serial 1

HD unit 1, idb = 0x1C44E8, driver structure at 0x1CBAC8

buffer size 1524 HD unit 1, V.35 DCE cable

The show controller command gives us this information. (There's a lot more output that this with this command, but it's unimportant for our purposes.) The router with the DCE end of the cable needs to supply a clock rate to the DTE, and we'll do just that with the interface-level clockrate command.

R3#conf t

Enter configuration commands, one per line. End with CNTL/Z.

R3(config)#int serial1

R3(config-if)#clockrate 56000

2d18h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up

In just a few seconds, the line protocol goes up and stays up.

When troubleshooting a connection, always run show interface first. If you see the combination shown below, the connection is physically fine but logically down. That's generally the result of a needed keepalive not being present. With Frame Relay, it's probably an LMI issue, but with directly connected serial interfaces the issue is most likely the DCE end of the connection not supplying clockrate.

R3#show interface serial 1

Serial1 is up, line protocol is down

Troubleshooting is a big part of the job, and it's a big part of the Cisco CCNA and CCNP programs as well. Know your show and debug commands and you're on your way to passing the CCNA!

In this CCNA case study, we'll take some basic switching and trunking theory and put it into action. We have two routers (R2 and R3) along with two switches (SW1 and SW2). R2 is connected to SW1 at fast 0/2, and R3 is connected to SW2 at fast 0/3. Both routers have IP addresses on the 172.12.23.0 /24 network.

For these routers to be able to ping each other, the switches must be able to communicate. These are two 2950 switches, and they're connected via two crossover cables. Before we worry about the router connectivity, let's make sure the trunk link is up between the switches with the "show interface trunk" command.

SW2#show interface trunk

Port Mode Encapsulation Status Native vlan

Fa0/11 desirable 802.1q trunking 1

Fa0/12 desirable 802.1q trunking 1

< output truncated for clarity >

The default mode of these switches is for the ports to run in dynamic desirable trunking mode, so we didn't even need to write a configuration to have the trunk form - it's already there!

R2 and R3's Ethernet addresses have already been configured, the trunk line is operational, and both ports are in VLAN 1. We'll ping R2's Ethernet interface from R3, and then R3's Ethernet interface from R2 to verify IP connectivity.

R2#ping 172.23.23.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.23.23.3, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms

R3#ping 172.23.23.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.23.23.2, timeout is 2 seconds:
!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms

With pings, exclamation points indicate IP connectivity, and periods indicate no connectivity.

So we've got connectivity! Now let's see if we still have that connectivity when the ports are placed into different VLANs. Cisco CCNA theory states that devices in different VLANs can't communicate without the intervention of a Layer 3 device, but let's see if that's true by placing R2 into VLAN 23. (VTP is already running on these switches.)

SW1#conf t

Enter configuration commands, one per line. End with CNTL/Z.

SW1(config)#int fast 0/2

SW1(config-if)#switchport mode access

SW1(config-if)#switchport access vlan 23

SW1(config-if)#^Z

Now that R2 and R3 are in separate VLANs, can they still send pings back and forth?

R2#ping 172.23.23.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.23.23.3, timeout is 2 seconds:
.....

Success rate is 0 percent (0/5)

R3#ping 172.23.23.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.23.23.2, timeout is 2 seconds:
.....

No, they can't. The difference is that they're now in separate VLANs, and devices in different VLANs can't communicate unless routing is taking place somewhere. Here, no routing is taking place, so the pings don't go through.

Put R3's switch port into VLAN 23, and try the ping again.

SW2#conf t

Enter configuration commands, one per line. End with CNTL/Z.

SW2(config)#interface fast0/3

SW2(config-if)#switchport mode access

SW2(config-if)#switchport access vlan 23

R3#ping 172.23.23.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.23.23.2, timeout is 2 seconds:
!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/8 ms

R2#ping 172.23.23.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 172.23.23.3, timeout is 2 seconds:
!!!!!

Now that R2 and R3 are in the same VLAN, pings can go through. This just proves the theory - that inter-VLAN communicate requires a Layer 3 device. Layer 3 switches are becoming more and more popular, but router-on-a-stick is still around - and we'll see how to configure that in our next tutorial!

Article Source : CCNA Exam Guide

Chris Bryant has sinced written about articles on various topics from CISCO CCNA, Personal Desktop and Cisco CCNP. . Chris Bryant's top article generates over 27100 views. to your Favourites.