When a child starts learning how to skateboard, they will likely want to do some tricks at some point or another. Using skateboard ramps is a great way to do this. Purchasing your own ramps or building your own ramps is an investment and should only be done if the child is an advanced skateboarder and is serious about the sport. There are various types of ramps available and all have their unique properties and are all designed for different things. The more serious rider should be sure to get a well crafted ramp because it is safer. Building your own and finding the cheaper ramps are certainly an option but there are also risks involved with doing that and parents should be aware of the dangers. When in doubt, most metropolitan areas have skate parks that can be used.
A launch ramp is a ramp that is designed to make the skateboarder go airborne. While in the air various tricks can be done before landing. This is something advanced skateboarders use and it is one of the more dangerous types of ramps. A wave is a type of ramp that can be skated up one side and down the other. They are usually purchased in sets with one half able to join the other. You can typically put a flat box between them and make a large curve, sharp slope or four ramp area. The configurations can be moved and altered depending on your needs.
Rails are long tubes that are ridden on and tricks are done on. These are also dangerous and used with the advanced skater. Rails, however, are safer when purchased because they are generally lower to the ground. Some people try to use already installed rails that are on steps. This is very dangerous as the steps will compound a fall and possibly increase chances of injury. Learning how to ride rails that are low to the ground is the safest alternative.
Ramps and rails can be found in sporting goods stores and specialty skateboard shops. Generally they can be purchased on the Internet or brick and mortar stores starting at approximately one hundred dollars and can increase to several hundred dollars depending on the quality. Skateboard ramps are a serious investment, take up a lot of room and can only be used under safe conditions. Therefore, most people who purchase them buy them for the serious enthusiast.
Skateboarding Ramps And Rails
Sooner or later, everyone who rides a skateboard, bike or inline skates wants to tackle a skateboarding ramp. So many cool skateboarding tricks can be performed on a ramp, and it is not too hard to build one at home. Having a ramp at home gives you a chance to practice your skateboarding moves in peace and quiet. After all, who wants to take a lot of beginners' wipe outs in public? With some plywood, a few pieces of 2" by 4", and the right tools, you can build your own skateboarding ramp at home.
The first step in building your ramp is to check out skateboarding ramps you like and measure heights and curves, keeping in mind your own skill level. Next, compile your notes and draw up your own plans. When you are happy with it, draw the curve of the transition (the side) shape onto a big enough piece of plywood. When it is right, cut the curve out using a jigsaw. Sand the edges by hand or use an electric sander.
To make the other transition, lay another sheet (or the other half of the first transition, if the scrap is big enough, on the floor. Take your completed transition and place it on top, transferring the curve with pencil. Cut and sand this transition and the sides for your skateboarding ramp are finished.
Brace the corners with a few two-by-fours. When you are positioning your transition shapes, you can save time by making the width the same as that of the flexible double ply you will be using for your skateboarding ramp itself. Screw the two-by-fours six inches apart to bear the weight of the floor. The better your work, the more durable and long lasting your skateboarding ramp will be. The screws should go from the inside out. Starting the holes with a drill will avoid splintering the wood.
Now you are ready to add the skateboarding ramp. Glue and nail the platform on, paying careful attention that no screws or nails are sticking out onto the ramp surface, otherwise, watch out for some severe tire damage! Finally, add a thin metal sheet to the bottom of the ramp for a smooth transition.
One last word: try your weight on your skateboarding ramp before you go for a test drive! Otherwise, your inaugural flight could be bumpy!
Both Dana Bradley & Fabian Toulouse are contributors for EditorialToday. The above articles have been edited for relevancy and timeliness. All write-ups, reviews, tips and guides published by EditorialToday.com and its partners or affiliates are for informational purposes only. They should not be used for any legal or any other type of advice. We do not endorse any author, contributor, writer or article posted by our team.
Dana Bradley has sinced written about articles on various topics from Social Issues, Video Games and Recreation and Sports. Dana Bradley writes about ,. Dana Bradley's top article generates over 450000 views. to your Favourites.